Kazralar Before fi lling the coolant system, determine what coolant mix is correct for your operating conditions. Always wear proper ear protection when cutting or gouging, unless sound pressure level measurements taken at the installed hypeetherm have verified personal hearing protection is not necessary per relevant international, regional, and local codes. Never bypass or shortcut the safety interlocks. Machine motion is selectable and is used for configurations with multiple plasma systems.
|Published (Last):||3 October 2009|
|PDF File Size:||7.95 Mb|
|ePub File Size:||10.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Kazralar Before fi lling the coolant system, determine what coolant mix is correct for your operating conditions. Always wear proper ear protection when cutting or gouging, unless sound pressure level measurements taken at the installed hypeetherm have verified personal hearing protection is not necessary per relevant international, regional, and local codes.
Never bypass or shortcut the safety interlocks. Machine motion is selectable and is used for configurations with multiple plasma systems. Warranty will hyperthherm void. Ne pas utiliser des outils optiques pour visualiser le faisceau du laser. Do not cut containers that have held combustible materials. I only ask to judge what I was originally told by the salesman Is there a hypfrtherm g-code for turning off torch height control?
Replace missing or damaged labels immediately. Tenga disponible un extintor de incendios cerca del lugar. The console also houses a relay PC board and a control PC board. Wear insulated gloves and boots, and keep your body and clothing dry. Each Hypertherm plasma system is designed hpyertherm be used only with specific Hypertherm torches.
See regulators in this section for recommendations. Hypertherm HPRXD hylertherm The forks must also be centered front to back and side to side to prevent tipping while moving.
This cutting equipment is designed for use only in an industrial environment. Off-valve The off-valve consists of 5 solenoid valves, a manifold block and a wiring harness with connector. The length of the hoses from the torch to the metering console are critical to cut quality and consumable life.
Empty and properly clean the hpdxd first. Use las antorchas especificadas en el manual. Never point the torch toward yourself or others. Screening and shielding Selective screening and shielding of other cables and equipment in the surrounding area may alleviate problems of interference.
Keep non-qualified personnel and children away. The ignition console converts 20 VAC control voltage from the power supply into high-frequency and high-voltage pulses kv to break over the torch electrode-nozzle gap.
A ground rod that meets all applicable local and national electrical codes must be installed within 6 m 20 ft of the table. The console manages the selection and flow mabual of all incoming es. This work should be performed only by qualified, licensed personnel. HyPerformance Plasma. Install this switch near the power supply for easy access by the operator. They are taped together to help prevent twisting.
Route the ohmic contact wire through the opening in the braided cover and the torch sleeve. Instruction manual Revision 2 Uncoil the first 2 hprxf 6. Keep hypertherj safety labels on your machine in good condition. Position the laser as manua, to avoid unintentional eye contact. The Hypernet PCB provides communication between components and is the source for the arc voltage needed for the torch height control.
You shall notify Hypertherm promptly upon learning of any action or threatened action in connection with any such alleged infringement and in any event no longer than fourteen 4 days after learning of any action or threat of actionand Hypertherm s obligation to defend shall be conditioned upon Hypertherm s sole control of, and the indemnified party s cooperation and assistance in, the defense of the claim.
The swirling of gas in the HPR torch is used to bias the taper to one side Do not stand, sit or lie on or touch any wet surface when using the plasma system. Document Outline Use protective screens or barriers to protect others from flash and glare. Computer and other control equipment. Skin protection Wear protective clothing to protect against burns caused by ultraviolet light, sparks, and hot metal.
Hypertherm does not and cannot make any guarantee or warranty regarding the safe use of the product in your environment. This is the grounding system that completes the path of the cutting current from the torch back to the power supply. Add coolant to the power supply until the tank is full. Provide a disconnect switch close to the power supply with properly sized fuses. Always use purified water in the coolant mixture in order to prevent damage to the pump and corrosion in the torch coolant system.
Handle and use compressed cylinders in accordance with applicable national and local codes. Connectors on these cables should have a metal housing and the shield, not the drain, should be connected to the metal housing of the connectors at each end of the cable.
Connect the power cord leads to the line disconnect switch following national and local electrical codes. Telephone Paging Volume Control 1. Note Hypertherm s interpretation of these new requirements is that unless a site-specific evaluation has been completed to determine that all dust generated is not combustible, the edition hyperrtherm NFPA 68 requires the use of explosion vents designed to the worst-case Kst value see annex F that could be generated from dust so that the explosion vent size and type can be designed.
Hypertherm HyPerformance HPR130XD Instruction Manual
Hypertherm HyPerformance Plasma HPR260 Instruction Manual